E-TECH RESEARCH, INC. UFOMATE P1414MX Card Type Modem(asynchronous) Chip Set Unidentified Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus External Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line in CN1 Power in CN4 Line out CN2 Power switch SW1 RS-232/422 CN3 DIAGNOSTIC LED(S) LED Color Status Condition TXD Red On Modem is transmitting data TXD Red Off Modem is not transmitting data RXD Red On Modem is receiving data RXD Red Off Modem is not receiving data DCD Red On Carrier signal detected DCD Red Off Carrier signal not detected LB Red On Battery is low (ten minutes power remaining) LB Red Off Normal operation Proprietary AT Command Set BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Default: Read only Range: 0 - 255 Description: Displays command echo, result codes, pulse/tone, buffer size and answer/originate Bit Value Function 0 0 Not used 1 0 Command echo disabled 1 Command echo enabled 2 0 Result codes enabled 1 Result codes disabled 3 0 Numeric result codes enabled Verbose result codes enabled 4 0 Not used 5 0 Pulse dialing enabled 1 Tone dialing enabled 6 0 Normal buffer size 1 Small buffer 7 0 Answer mode 1 Originate mode BIT-MAPPED REGISTER S21 Format: AT [cmds] S21=n [cmds] Default: 32 Range: 0 - 255 Description: Controls DTR, DCD and long space disconnect Bit Value Function 4, 3 00 DTR ignored 01 Escape command state on low DTR, remain off hook 10 Go on hook and auto answer disabled 11 Reset on low DTR 5 0 DCD forced high or Computer Systems Interface compliant 1 DCD normal or Port Contender compliant 6 0 Not used 7 0 Long space disconnect disabled 1 Long space disconnect enabled BIT-MAPPED REGISTER S22 Format: AT [cmds] S22=n [cmds] Default: 68 Range: 0 - 255 Description: Controls speaker, extended result codes and Break/make ratio Bit Value Function 3, 2 00 Speaker disabled 01 Speaker disabled until DCD high 10 Speaker enabled 11 Speaker after dialing until DCD high 6, 5, 4 000 Disabled 001 Enable extended result codes 010 Enable extended result codes and dial tone detect 011 Enable extended result codes and busy signal 100 detect Enable dial tone detect and busy signal detect 7 0 Break/make ratio 61/39 1 Break/make ratio 67/33 BIT-MAPPED REGISTER S23 Format: AT [cmds] S23=n [cmds] Default: 23 Range: 0 -255 Description: Controls test options, serial port speed, parity and guard tone Bit Value Function 0 0 Remotely requested remote digital loopback disabled 1 Remotely requested remote digital loopback enabled 1 0 DTE speed of less than 2400bps only enabled 1 DTE speed of 2400bps or greater only enabled 2 0 DTE speed of less than 1200bps only enabled 1 DTE speed of 1200bps or greater only enabled 4, 3 00 Parity even 01 Parity space 10 Parity odd 11 Parity null 6 00 Guard tone disabled 01 550Hz guard tone enabled 10 1800Hz guard tone enabled BIT-MAPPED REGISTER S24 Format: AT [cmds] S24=n [cmds] Default: 2 Range: 0 - 255 Description: Controls compromise equalization Bit Value Function 3, 2, 1, 0 0000 0dB equalization 0001 2dB equalization 0010 4dB equalization 0011 6dB equalization 0100 8dB equalization 0101 10dB equalization 0110 12dB equalization 0111 14dB equalization BIT-MAPPED REGISTER S28 Format: AT [cmds] S28=n [cmds] Default: 49 Range: 0 - 255 Description: Controls speaker and error correction Bit Value Function 3, 2, 1, 0 0000 Speaker disabled 0001 Speaker disabled until DCD high 0010 Speaker enabled 0011 Speaker while dialing until DCD high 7, 6, 5, 4 0000 Normal mode 0001 Auto MNP mode 0010 MNP mode 0011 Auto V.42 mode 0100 LAPM mode BIT-MAPPED REGISTER S29 Format: AT [cmds] S29=n [cmds] Default: 16 Range: 0 - 255 Description: Controls DTR and carrier control Bit Value Function 3, 2, 1, 0 0000 DTR ignored 0001 Escape command state on low DTR, remain off hook 0010 Go on hook and auto answer disabled 0011 Reset on low DTR 7, 6, 5, 4 0000 DCD forced high 0001 DCD follows remote modem 0010 Conforms to Computer Systems Interface 0011 Conforms to Port Contender BUFFER SIZE Type: Configuration Format: AT [cmds] $Bn [cmds] Description: Controls buffer size Command Function $B0 Normal buffer size (2.2K) $B1 Reduce buffer size to 1.5K CANCELER Type: Configuration Format: AT [cmds] $An [cmds] Description: Controls echo canceler length Command Function $A0 Standard canceler enabled $A1 Long canceler for round trip delays of over 36.833ms enabled CARRIER DETECT Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Controls DCD, Computer Systems Interface and Port Contender Command Function &C0 DCD forced high &C1 DCD follows remote modem &C2 Conforms to Computer Systems Interface &C3 Conforms to Port Contender COMPRESSION Type: Configuration Format: AT [cmds] $Cn [cmds] Description: Controls data compression Command Function $C0 Data compression disabled $C1 Data compression enabled CONNECT/SPEED MESSAGE Type: Configuration Format: AT [cmds] $Xn [cmds] Description: Controls connect and speed message displayed Command Function $X0 Normal connect and DCE speed message enabled $X1 Normal connect and DTE speed message enabled $X2 Extended connect and DCE speed message enabled $X3 Extended connect and DTE speed message enabled DIAL INTERRUPT Type: Configuration Format: AT [cmds] $Kn [cmds] Description: Controls dial interrupt Command Function $K0 Dial interrupt disabled $K1 Dial interrupt enabled DISPLAY STORED INFORMATION Type: Configuration Format: AT [cmds] &Vn [cmds] Description: Displays stored phone numbers, configuration profiles and S registers Command Function &V0 Display stored phone numbers &V1 Display current configuration profiles &V2 Display contents of S registers &V3 Display stored profiles briefly DSR SIGNAL Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Controls DSR, Computer Systems Interface and Port Contender Command Function &S0 DSR forced high &S1 DSR follows remote modem &S2 Conforms to Computer Systems Interface &S3 Conforms to Port Contender EQUALIZATION Type: Configuration Format: AT [cmds] $Qn [cmds] Description: Controls compromise equalization Command Function $Q0 0dB equalization $Q1 2dB equalization $Q2 4dB equalization $Q3 6dB equalization $Q4 8dB equalization $Q5 10dB equalization $Q6 12dB equalization $Q7 14dB equalization FLOW CONTROL Type: Configuration Format: AT [cmds] $Fn [cmds] Description: Controls XON/XOFF, ENQ/ACK, DTR/DSR and CTS/RTS flow control Command Function $F0 XON/XOFF enabled $F1 XON/XOFF passthrough enabled $F2 ENQ/ACK enabled $F3 DTR/DSR enabled $F4 CTS/RTS enabled $F5 Flow control disabled INACTIVITY TIMER Type Configuration Format AT [cmds] S36=n [cmds] Default 0 Range 0 - 255 Unit 1 minute Description Sets length of time the modem waits before disconnect if no data sent or received LINE SPEED Type: Configuration Format: AT [cmds] S37=n [cmds] Description: Controls speed at which modem attempts to connect Command Function S37=0 Line speed follows DTE speed. If DTE is over 9600bps, attempt connect at 14.4Kbps S37=1 Connect at V.23 75/1200bps S37=2 Not used S37=3 Connect at 300bps S37=4 Not used S37=5 Connect at 1200bps S37=6 Connect at 2400bps S37=7 Connect at 4800bps S37=8 Not used S37=9 Connect at 9600bps S37=10 Not used S37=11 Not used LINE SPEED Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Controls speed at which modem attempts to connect Command Function &L0 Line speed follows DTE speed. If DTE is over 9600bps, attempt connect at 14.4Kbps &L1 Connect at V.23 75/1200bps &L2 Not used &L3 Connect at 300bps &L4 Not used &L5 Connect at 1200bps &L6 Connect at 2400bps &L7 Connect at 4800bps &L8 Not used &L9 Connect at 9600bps &L10 Not used &L11 Not used PARITY Format: AT [cmds] S30=n [cmds] Default: 0 Range: 0 - 255 Description: Controls parity Bit Value Function 1, 0 00 Parity space 01 Parity even 10 Parity null 11 Parity odd PROTOCOL Format: AT [cmds] S27=n [cmds] Default: 64 Range: 0 - 255 Description: Selects data modulation protocol Bit Value Function 0 0 ITU-T mode 1 Bell mode PROTOCOL Type: Configuration Format: AT [cmds] $En [cmds] Description: Controls protocol used Command Function $E0 Normal mode $E1 Auto MNP mode $E2 MNP mode $E3 Auto V.42 mode $E4 LAPM mode RETRAIN Format: AT [cmds] S15=n [cmds] Default: 5 Range: 0 -255 Description: Controls number of retrains per minute allowed Bit Value Function 3, 2, 1, 0 0000 Not used 7, 6, 5, 4 0000 Disconnect If more than four retrain attempts in three minutes 0001 Disconnect If more than four retrain 0010 attempts in four minutes 0011 Disconnect If more than four retrain attempts in five minutes 0100 Unlimited retrain allowed Retrain disabled RETRAIN LIMIT Type: Configuration Format: AT [cmds] &En [cmds] Description: Controls number of retrains per minute allowed Command Function &E0 Disconnect If more than four retrain attempts in three minutes &E1 Disconnect If more than four retrain attempts in four minutes &E2 Disconnect If more than four retrain attempts in five minutes &E3 Unlimited retrain allowed &E4 Retrain disabled SPEED CONVERSION Type: Configuration Format: AT [cmds] $Sn [cmds] Description: Controls speed conversion Command Function $S0 Speed conversion enabled $S1 - $S8 Speed conversion disabled TEST STATUS Format AT [cmds] S16=n [cmds] Default: Read-only Range: 0 - 255 Unit: Bit-mapped Description: Contains status of loopback tests Bit Value Function 0 0 Local analog loopback test disabled 1 Local analog loopback test enabled 1 0 Not used 2 0 Local digital loopback test disabled 1 Local digital loopback test enabled 3 0 Remotely requested remote digital loopback enabled 1 Remotely requested remote digital loopback disabled 4 0 Locally requested remote digital loopback test not in progress 1 Locally requested remote digital loopback test in progress 5 0 Remote digital loopback with local self-test disabled 1 Remote digital loopback with local self-test enabled 6 0 Local analog loopback with local self-test disabled 1 Local analog loopback with local self-test enabled 7 0 Not used TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] $Tn [cmds] Description: Controls transmission level Command Function $T0 - $T4 -10dBm $T5 -10dBm $T6 -12dBm $T7 -14dBm $T8 -16dBm BITS PER CHARACTER Type: Configuration Format: AT [cmds] $Ln [cmds] Description: Sets character length while in data mode Command Function $L0 8 bits per character $L1 9 bits per character $L2 10 bits per character $L3 11 bits per character